Installation of EPDM Rubber Flooring

1. Make sure no sand or crack on the ground, the flatness of ground is more than 95%, no obvious gradient and keep dry & clean, no residues, dust etc.

2. Apply polyurethane primer on the concrete surface.

3. Elastic shock-absorbent, mixture of PU binder and SBR granules.

4. Apply polyurethane primer on the SBR surface.

5. Top elastic layer, mixture of PU binder and coloured EPDM granules.

6. Final Cleaning.

Installation of Vinyl Floor

Vinyl flooring must be laid on a perfectly smooth and level floor. If the floor is damaged, take extra care in the preparation.

Concrete floor: Remove all dust. Fill any cracks and rub down any uneven patches. If required, apply a screed to fully level the floor.

Old tiling: Remove any loose tiles and fill the space with concrete. Scrub the floor with detergent before applying a screed to ensure a perfectly flat surface.

Old laminate flooring: Ensure that it has been firmly stuck down. If not, take it up.

You will need:

1. Metal Ruler
2. Spatula Trimming Knife
3. Semi-Free Installation: Double-sided adhesive tape.
4. Fixed Installation: A finely serrated spatula, Strong acrylic glue.

How to lay your floor?

The day before fitting, unroll your flooring in the room where it is to be laid and leave for 24 hours at room temperature.

If your home has underfloor heating, turn it off preferably 24 hours(including preparation time) before fitting the floor.

Cover the entire surface of the room leaving a 5cm excess at the base of the walls. Joints can be made in two ways:

1. By laying the edges side by side.

2. By overlapping the edges and cutting to fit.

Follow the direction of laying (In general, the lengths are reversed).

Try not to leave any gaps at the joints or lay the edges too tightly together (This may result in unsticking over time).

The next stage differs according to the type of fitting.

Fixed Fitting:

This is essential in rooms over 30 sq.m. or in heavy use, ensuring maximum stability and durability.

– Fold the length back partially and apply adhesive using the finely serrated spatula (this stops furrows appearing).

Observe the recommended amounts (Approx.250g/m2) and the sticking time required for the smooth application and drying of the adhesive: to be sure, refer to the manufacturer’s instructions on the packaging.

– Fold down each length and fix firmly moving from the centre of the room towards the walls. This will expel any air trapped between the floor and the flooring.

Semi-Free fitting  (using double-side adhesive tape): Suitable for rooms less than 30 sq.m. and subject to normal traffic.

– Lift the flooring and place double-sided adhesive tape around the perimeter of the room and under the joints to keep them in place.

– Lay the length back down and press hard.

Free Fitting: Suitable only for small rooms subject to low traffic.

Finishing Off:

Along the skirting boards, remove the excess using the trimming knife and spatula.Tips of the trade:

– Laying your event floor on stairs. Use the fixed (Adhesive) method for maximum long-term hold.

– The joints are still visible in parts. Use a cold solder.


– Live in harmony with your vinyl floor. Whatever the size of your family, taking care of your trendy floor couldn’t be easier.

Regular Care:

Simply remove dust with a brush or vacuum cleaner.

Weekly Care:

Mop with water and a mild household detergent for optimal cleanliness. You may wish to clean more or less often according to how heavily used an area is.

Please Note: Your floor may be disinfected with diluted bleach daily or as required.

Installation of TigerTurf Artificial Grass Turfs

To get the best from your TigerTurf artificial grass turf, it must be installed by experienced, trained fitters working to exacting standards. In all instances, TigerTurf is on hand during and after installation to offer expert advice that will produce the very best performance from your artificial turf surface.

TigerTurf works closely with suppliers of specialist adhesives so that every seam is jointed correctly. This includes playing lines, which are cut in, and augmenting lines, which are tufted in during manufacture.

The choice of infill materials is important if TigerTurf’s artificial grass systems are to perform to the standards laid out in test procedures. TigerTurf specifications clearly state the necessary grade of infill material, and TigerTurf works closely with the providers of quality infill.

Visual inspections of the completed artificial grass turf can be backed up by independent tests on seam strength, tuft withdrawal and other sports requirements such as ball roll and bounce.

TigerTurf’s research and development unit carries out field tests to verify that the synthetic grass turfs are installed according to TigerTurf’s exacting standards.